Industrial Paints

Product Details:

A two pack high solid epoxy prime containing high level of zinc phosphate anticorrosive pigment the easy to apply.

Product Details:

A build anticorrosive primer based on chlorinated rubber incorporating zinc phosphate as the passivating pigment.

Product Details:

If settling is observed in the drum, loosen the settled material with the help of hand stirrer followed by power driven stirrer for quick homogenous mixing.

As a general safety measure, inhalation of solvent vapours or paint mist and contact of liquid paint with skin and eyes should be avoided. Forced ventilation should be provided when applyingpaint in confined spaces or stagnant air. Even when ventilation is provided, respiratory, skin and eye protection are always recommended when spraying paint.Please refer to our Material Safety Data Sheet prior to using the product.

Features:

• Anti-corrosive primer for conventional system
• Can be top-coated with conventional or chlorinated rubber coatings
• Easy application by brush and conventional spray

Product Details:

Zinc rich coatings are porous and hence pinholes may occur in the subsequent coat due to solvent popping. To minimize pinholes, apply a mist coat as the first pass of the subsequent coat, let the entrapped air escape and then apply full coat. Zinc rich primers, when exposed for extended periods of time without proper top coating, will start showing white rust formation. These “white rust” spots are zinc corrosion products. The extent of white rust formation will depend on the period of exposure of the zinc rich coating and the nature of the surrounding environment. Prior to application of the subsequent coats, it is necessary to ensure removal of the white rust. 

Product Details:

Guideline is specially formulated for applying on concrete or Butimen covered concrete as marking
paint visible from a large distance. The product can also withstand abrasion and endure
environmental tortures. This product will satisfy IS - 164/1981 specification requirements

Product Details:

MIO is a type of iron oxide similar to mica, a highly structured, layered mineral. As MIO pigments are ground into smaller, finer particles, they tend to stick to their surfaces, exposing smooth, shiny faces which behave like tiny mirrors. It was found that MIO coatings and paints produces excellent anti-corrosion paint. It is used as the primary ingredient in some protective coatings and primers because of its anti-corrosive properties. When attached to the coating and applied to the substrate, flakes align parallel to the surface providing an impermeable barrier to air, oxygen and chemicals. The flakes are highly weather-resistant and powerful UV absorbers

Product Details:

A high solid coal tar epoxy coating with outstanding performance in highly saline, chemical and most severe corrosive environments.

Product Details:

Inorganic zinc silicate (IOZS) coatings comprise metallic zinc held in
a glassy silicate matrix. The zinc metal provides galvanic corrosion
protection to the mild steel substrate, whilst the coating’s porosity
provides voids that contribute to ongoing protection to the mild steel

Product Details:

Recommended for use on aluminum cladding, galvanised rails or pipes, metal sprayed steel gantries etc.

Product Details:

epilux 610 is a general purpose epoxy anti-corrosive primer used as a blast or holding primer in new construction structural steel and as a lining in water tanks. The product offers excellent anti-corrosive performance, good wetting properties and outstanding adhesion to blasted steel.

Product Details:

Two pack, polyamide cured, air drying high build epoxy primer containing zinc phosphate pigments.

Ensure that the concrete surface is cured for minimum 3 months. In case of large areas and for severe exposure conditions, the surface has to be prepared by light blasting. In less critical areas where blasting is not practical, wire brushing has to be adopted to remove lattices, followed by treating with dilute (10%) hydrochloric acid.

Remove acid and contaminants by liberal wash with water. Ensure that acid solution does not retain on the surface & joints. Allow the surface to dry thoroughly before applying primer.

Features:* Designed for use as a primer for steel as well concrete* Excellent resistance to saline, marine and chemical environments* Good adhesion properties for subsequent coats* Good adhesion on concrete, steel and aged epoxy coatings

Product Details:

It is an oil modified alkyd based BP Zinc Yellow Primer suitably pigmented with micro fine pigments and extenders.

Product Details:

If settling is observed in the drum, loosen the settled material with the help of hand stirrer followed by power driven stirrer for quick homogenous mixing.
Condition:

• Suitable Chlorinated Rubber/ Conventional/ Epoxy primers or intermediates; dry and free from all contamination. In case of aged Epoxy/ conventional coating, the surface should be sufficiently roughened prior to painting
• Surface temperature must be atleast 3 C above dew point but not above 50 C

Features:

• Topcoat/ buildcoat in chlorinated rubber systems
• Suitable for interior and exterior use
• Fast drying
• Dry heat resistance upto 60 C

Product Details:

Surface Preparation condition:

• Steel; blast cleaned to Sa 2.5 of Swedish specification
• If blast cleaning is impractical, remove loose rust/ scale using power tools/ hand tools to achieve St3/ St2 grade of surface preparation as per Swedish standards
• Suitable zinc primer, epoxy primer or epoxy intermediate coat; dry & free from all surface contamination. In case of aged epoxy coating, the surface should be sufficiently roughened prior to painting
• Surface temperature should be at least 3 above dew point and not above 50 C

Features:

• Good resistance to corrosion in marine exposure and subsoil conditions
• Good abrasion resistance
• Good chemical resistance
• Excellent water resistance